I would buy again!
Adjustable to less than 3-lb pull.
Safety
TriggerTech is committed to the highest level of quality and safety. In keeping with that commitment, we have established this page to provide relevant safety information to our customers.
TriggerTech Recalls Carbide Triggers Due to Cracking of Carbide Rollers
In keeping with TriggerTech’s commitment to safety we are conducting a voluntary recall in response to a condition we identified with triggers that utilized carbide rollers “Carbide Triggers.” This recall applies to all Carbide Triggers which were manufactured between June 5, 2015 and July 28, 2016.
In one recent case, a carbide roller cracked and remained intact in a Rem 700 Carbide Trigger for approximately 2,000 rounds. The cracked carbide roller caused accelerated and unusual wear. A gradual reduction in pull weight was observed and the trigger eventually got to the point where the rifle, with the safety off, could discharge without trigger activation. In TriggerTech’s spirit to always do the right thing TriggerTech is voluntarily recalling all Carbide Triggers.
This voluntary recall involves REM 700 Carbide Triggers, AR15 Carbide Triggers, and Excalibur, Mission, Killer Instinct and Parker Crossbow Carbide Triggers. Carbide Triggers can be identified by their serial number or date code. The serial number/date code can be found on the side of the Rem 700 triggers, and on the bottom of the AR15, Killer Instinct, Excalibur, Mission, and Parker triggers.
By the end of July 2016, TriggerTech transitioned to 100% stainless steel roller production in response to reports of cracking carbide rollers in crossbow triggers (these reports did not give cause for safety concerns). Stainless steel rollers are significantly stronger and more impact resistant than carbide rollers and TriggerTech has determined that stainless steel rollers will not exhibit the same potential cracking issue as carbide rollers.
TriggerTech will correct any and all potential conditions at no cost to the consumer as part of our 100% Satisfaction Guarantee.
Click here or select the CHECK button below to go through the identification process of seeing if you have an effected trigger.
Carbide Roller Recall Summary
Name of Product: Trigger Tech triggers which utilize a carbide roller (“Carbide Triggers”)
Hazard: Certain carbide rollers can crack and the trigger may continue to function. Extended use (2000 +/- cycles) with a cracked carbide roller may cause accelerated and unusual wear and, if the weapon’s safety is off, subsequent discharge of the weapon may occur without trigger activation posing an injury hazard to the user or bystander.
Remedy: Replace
Consumers should immediately stop using the recalled triggers and contact TriggerTech for a free replacement trigger with a stainless-steel roller. TriggerTech will offer a full refund instead of the replacement trigger if the recalled item has been discontinued.
Consumer Contact: TriggerTech toll-free at 888-795-1485 from 9 a.m. to 5 p.m. Monday through Friday, online at www.triggertech.com and click on “Recalls” for more information.
Recall Details
Units: About 4,000
Product Description: This recall involves all TriggerTech Carbide Triggers. The following table describes the Carbide Triggers that are being recalled:
Carbide Trigger Identification:
Carbide Triggers can be identified by the following serial numbers/date codes that are engraved on the outside of the trigger housing. In some cases, there are shortcuts you can use to determine if you have a Carbide Trigger without referencing the serial number/date code. Please go to safety.triggertech.com for detailed instructions on how to determine if you have a Carbide Trigger.
The serial numbers / date codes of the recalled Carbide Triggers are listed in the table below:
Incidents/Injuries: None reported
Sold at: This Recall involves six models of Carbide Triggers that were manufactured between June 5, 2015 and July 28, 2016 and were sold: i) direct from TriggerTech for about $120 to $190 (web/phone); ii) through retailers and dealers nationwide; and iii) installed in Guns/Crossbows Manufactured by: Prairie Gun Works (R700), Gunwerks (R700), SAC Firearms (Rem 700) and Killer Instinct (Crossbow)
Manufacturer: TriggerTech
Manufactured in: Canada
Photos:
Rem 700 |
AR15
|
Killer Instinct
|
Excalibur
|
Mission
|
Parker
|
CLICK HERE TO CHECK YOUR TRIGGER FOR RECALL
NRA Gun Safety Rules
Always following the NRA Gun Safety Rules.